General | Frequency
range | 100Hz to8.5GHz |
Maz.input
level
(continuous
wave
average
power) | +40dBm(10W) |
Referenceoscillator | Frequency:10MHz
Startingcharacteristics:≤5×0.00000001/day(option:≤2×0.00000001/day after30min.warm-up)
*After 10min.of warm-up,compared to the frequency after 24-hourwarm-up
Aging rate:≤2×0.00000001/day(option:≤5×0.000000001/year)
*Compared to the frequency after 24-hour warm-up
Temperaturecharacteristics:5×0.00000001/day(option:3×0.00000001/day)
*0to 50℃,relative to the frequency at 25℃ |
Spectrum
anallyzer | Frequency | Settingrange:100Hz to 8.5GHz(resolution:1Hz),0to2GHz(freq.band:0),1.7to7.5GHz(freq.band:1-),6.5to8.5GHz(freq.band:1+)
Preselector range:1.7to 8.5GHz (bands:1-/1+)
Display accuracy:±(display freq.×reference freq.accuracy+span×spanaccuracy)
Span
Setting range:0Hz,100Hz to 8.5GHz
Accuracy: ±2.5%(span≥1kHz),±5%(100Hz≤span<1kHz)
RBW
Setting range:10Hz to 3MHz(3dB),1-3serqence
Accuracy:±20%
Selectivity(60/3dB);≤15:1(100kHz to 3MHz),≤12:1(10Hz to 30kHz)
VBW:1Hz to 3MHz,off,1-3 seqrence
Signal purity(SSB,1MHz to 4GHz):
≤-100dBc/Hz(10kHz offset,≤-115dBc/Hz(50kHzoffset),≤-120dBc/Hz(100kHzoffset) |
Spec-
trum analyzer | Ampl-
itude | Level | Level measuringrange:Average:Average noiselevl to +40dBm
Average noise level:≤-112dBm(10MHz to 8.5Ghz,RBW 10Hz,VBW1Hz,input att.setting20dB)
Residual reponse:≤-75dBm(1MHz to 8.5GHz,input att.setting20dB) |
Reference
level | Settingrange:-80to +40dBm
Accuracy:±0.5dB(-30to +20dBm),±0.75dB(-40to -30dBm,+20to+40dBm),±1.5dB(-60to-40dBm)
*After calibration and at freq.100Mhz,span≤2MHz,and in auto modefor inputatt ,RBW,VBW and sweep time settings
RBW switching error(aftercalibration):±0.3dB(RBW:≤300kHz), |
Frequencyreponse | ±0.5dB(100MHzto 2GHz,band:0),±1dB(1.7to8.5GHz,bands:1-/1+) |
Linearity(
after calibration) | LOG:±0.3dB(0to-20dB,RBW:≤100kHz),±1.5dB(0to-80dB,RBW≤10kHz)
LIN:±5%(to reference level) |
Dynamic
range | 2ndharmonics:
≤-70dBc(5to 800MHz,band:0,mixer input level:-30dBm)
≤-80dBc(800to 850MHz,band:0,mixer input level:-30dBm),
≤-90dBc(850MHz to 2.1GHz,bands:1-,mixer input level:-10dBm)
Two-signal third-ouder intermodulation distortion:≤-70dBc(10to50MHz),≤-85dBc(50MHzto 2.1GHz)
*Frequency difference between two signals≥50kHz,mixer inputlevel:-30dBm |
Sweep | Sweep time
Setting range:20ms to 1000s(TRACE-FREQ,data points:NORMAL),50ms to1000s at other conditions
Accuracy:±10%(20ms to 200s),±15%(200 to 1000s)
Sweep mode:CONTINUOUS,SINGLE
Trigger:FREE RUN,TRIGGERED
Trigger source:VIDEO,LINE,EXT(±10V),EXT(TTL)
Gate mode(OFF,random sweep mode)
GATE DELAY:0to 65.5ms(in 1μs steps,GATE END:INT)
GATE END:INT/EXT |
Time
domain
waveform
display | Sweepfime:50,100to 900μs(data point:NORMAL,Onemost significant digit canbe set.)
1ms to 1000s(data point:NORMAL,Two most significant digits can beset)
100,200to800μs(data point:DOUBLE,One most significant digit can beset aseven number.)
1ms to 1000s(data point:DOUBLE,Two most significant digits can beset aseven number.)
Delay time
Pre-trigger.-time span to 0s(in 1point steps)
Post trgger:0to 65.5ms(in 1μssteps)
Amplitude display resolution:50μsto 49ms,10bits*0.1%of fullscale)
50ms to 1000s,14bits(0.01%of full scale) |
Detection
mode | POS PEAK,SAMPLE,NEG PEAK |
Number
of
points | NOUMAL:501points,DOUBLE:1002points |
AM/FM
demodu-
lation | Demodulatedwaveform display and monitoringdemodulated audio signal withinternal speaker |
| | Auxiliaryinputs/
outputs | IFoutput21.4MHz:-10dBm±2dB(at top of
screen,with output terminated by 50Ωteminator),BNC connector
Youtput:0to 0.5V±0.1V(at range between
top and bottom of screen,LOG:10dB/div,LIN:10%/div,100MHz
and with output terminated by 75Ω
terminator),BNC connector
External trgger input
Input1:max.±10V(in 0.1V steps,
rising/falling edges selectable
and pulse width≥10μs),BNC connector
Input2:TTL level(rising/falling
edges selectable and pulse width≥10μs,
)BNC connector |
Powermeter | Frequencyrange | 100kHz to5.5GHz |
Levelrange | -20to+20dBm |
Instrumentation
accuracy | ±0.5% |
Zeroset | ±0.5% of fullscale at most
sensitive range(100μW range) |
Zero shiftbetween
ranges | ±0.2% of fullscale zero setting at mostsensitive range |
Calibrationoscillator | Freq:50MHz,Output:1.00mW,Accuracy:±1.2% |
Applicablepower
sensor | MA4601A |
Others | Display | 640×400dot,9-inch EL |
Inputs/outputson rear panel | Referenceinput:10MHz±10Hz,2to 5Vp-p,
≥50Ω,BNC connector
Reference buffer output:10MHz,2to
3Vp-p(with the output terminated by
200Ω terminator),BNC connector
Separate video output:Compatible
with 8-pin DIN connector |
Externalmemory | One slot forcan be connected |
Save/recall | Internalmemory(4sets of spectrum
and Tx test conditions),can
save/recall setting conditions
at extemal memory(PMC) |
Directplotting | Can hard-copyscreen via GPIB2 |
Externalcontrol | GPIB1
(IEEE488.2) | As devicecontrolled by host,all
functions except power swetch
Controls other instruments as controller
using PTA
SH1,AH1,T6,L4,SR1,RL1,PP0,DC1,DT1,
C0(C1,C2,C3,and C24with PTA) |
GPIB2
(IEEE488.1) | Controls otherinstruments as controller
SH1,AH1,T6,L4,SR1,RL1,PP0,DC1,DT1
,C1,C2,C3,C4,C28 |
I/Oport | Output portA/B:8-bit(TTL level),
Input/Output port C/C:4-bit(TTL level),
EXclusive port:3-bit(TTL level)
Control signal:4(TTL level),+5V
output:Max.50mA |
RS-232C
(Option 02) | Controls otherinstruments as
controller |
PTA | Language | PTL:High levellanguaeg interpreter
based on BASIC |
Programming | Using externalkeyboard |
Program
memory | On PMC orFD
Upload/download from/to PC |
Programmingcapacity | 900KB |
Operatingtemperature | 0°to50℃ |
Power | 85to 132/170 to250Vac,47.5 to 63Hz
,≤500VA |
Dimensions andmass | 426(W)×221.5(H)×451(D)mm,≤27kg |
EMC*1 | EN55011:1991,Group1,ClassA
EN50082-1:1992 |
Safety | EN61010-1:1993(Installation CategoryII
,Pollution DegreeII) |